[Tray]

[Smartphone Holder]

[Center Panel]

Designed specifically for the Jimney (JB64) Gymnie Sierra (JB74)
This is a new product that removes the factory panel on the top of the center air conditioner of the Jimney (JB64) Jimney Sierra (JB74) and converts the M8 nut into a panel with a built-in M8 nut. Exclusive design/exclusive design that fits perfectly into your gym neys interior and allows you to install it without any discomfort.

Sleek and exclusive design.
Designed specifically for Gymnies, so it is made of resin that is the same color as the interior color of Gymnys rather than the typical black resin. The body surface has been treated to be similar to the interior of the gym to give it a finished look that is like the original. The M8 bolt on the base is removable and can be replaced with the stock M8 bolt.
Hex wrench (0.24 inch (6 mm) is required to remove the product. Hex wrench not included.

Dedicated so it can be installed perfectly.
The original equivalent clip allows you to attach it to your gym panel perfectly. Also, you just need to replace the original panel position, so there is no damage or residue around you.

Comes with a tool to remove the original panel (estimated duration: 3 minutes).
Includes tools for removing panels (upholstery) necessary for installation work.
Simply remove the original panel according to the instruction manual and replace it with this product, so if you are a good job at work, you can complete installation work in about 1 minute, even if you are not satisfied with the product, you will be able to complete the installation process.
The working time is an estimate.

Installation Method (Overview)
Installation location: Upper center air conditioner / panel under navigation
Installation Method: (Please be sure to read the instruction manual when installing. )
1. Remove factory panels
Insert the included tools from the bottom of the panel between the panel and the panel You can remove the clip and remove the panel by pulling the tool forward to the fulcrum.
2. Install the product on the location where you have removed the factory panels.
(Be careful not to insert it in the wrong direction. Insert the recessed end into the handle side. )

Contents:
Base: M8 bolts x 2
(2) (M8 bolts are packed with attached to the base. )
Accessories: Panel (lining) peeling

● Before you buy
This product is only for the following right hand drive vehicles:
(This is an information based on the research current in February 2022 (Reiwa 4). (Subsequent vehicles will not be investigated. )]
Suzuki Jimney (JB64 2018 (From July 2018)
Suzuki Jimnie Sierra (JB74 2018 from July 2018)
If the factory optional navigation panel is installed, this product cannot be installed.

● Please read
[Note]
Do not attach objects that will interfere with driving.
Before using, make sure that the items attached to this product and are firmly secured. It may fall off or fall off.
Do not attach or hook objects at the base of this product with a total of 28.6 oz (800 g).

From the Manufacturer

For Jimney (JB64) Jimney Sierra (JB74)

This product is only compatible with the following right hand drive vehicles: [As of March 2022 (Reiwa 4) (Subsequent vehicles are not investigated)]

■Suzuki Jimney (JB64 2018 (Heisei 30) July

■Suzuki Jimnie Sierra (JB74 2018 (Heisei 30) July and Up)

*This product will not be able to install if the factory optional navigation panel is installed.

Just like a genuine gym center panel.

This is a new product that removes the factory panel on the top of the center air conditioner of the Jimney (JB64) Jimney Sierra (JB74) and converts the M8 nut into a panel with a built-in M8 nut.Exclusive design/exclusive design that fits perfectly into your gym neys interior and allows you to install it without any discomfort.

The M8 bolt on the base is removable and can be used for DIY projects such as replacing the M8 bolts on the market.

(more)

Center panel that doubles as a DIY base part

Sleek, exclusive design Made of resin that is the same color as the interior color. The body surface has been treated to be similar to the interior of the gym to give it a finished look that is like the original.	Do-it-your-selfers Two removable M8 nuts embedded in the panel. Can also be used for DIY purposes such as replacing the M8 bolts on the market. Hex wrench (0.24 inch (6 mm) is required to attach or detach the bolt on this product. Hex wrench not included.	Bolt fitting part size (Attachable Bolts) Dimensions: M8 Thread Pitch: 1.25 Load Capacity: Total 800g

(more)

Installation Instruction *Please check the instruction manual for detailed installation instructions.

1. Remove factory panels Insert the included tools from the bottom of the panel between the panel and the panel Pull the tool forward to the fulcrum of the inserted portion to release the clip and remove the panel easily.	2. Install this product on the location where you have removed the factory panel. The claws are inserted into the hole where the factory panel is inserted. Just replace the factory panel position and no damage or residue around you.	M8 bolts are removable M8 bolts can be removed with a hex wrench (6mm) Can be used for DIY applications such as replacing M8 bolts on the market. Hex wrench (0.24 inch (6 mm) is required to remove the product.Hex wrench not included.

(more)

	Drink Holder	Rearview Mirror	Power Supply Unit	Cargo Tray (Trunk Mat)	Tray	Dress Up Parts
Item No.	NZ810	NZ820	NZ587	IA810	NZ819	DZ529
Product	Driver/Passenger Side Drink Holder	The rear-view mirror is a gentle curved surface that ensures a wide field of vision and a natural sense of distance.	Power supply unit that can be expanded to 2 sockets and 2 USB cables.	Waterproof 3-ply soft material tray	The perfect tray for storing small items	Dress up parts for easy dressing up
Fits Gymnie (H30.7 and up)	○	○	○	○	○	○
Fits Jim Knee Sierra (H30.7 and up)	○	○	○	○	○	○