Point the lid that covers the grid wrap.The Grid Trap lid is made of heavy steel sheet and has continuous non-slip nibs on the surface.It is necessary to maintain a load capacity that will not break even by humans, corrosion resistance and water resistance to protect metal from corrosion, most popular lids are made of iron or stainless steel.It also acts as an anti-odor effect that traps odors caused by gripping wraps. However, the gripping traps will again due to rust, corrosion, or breakage, and if left as is, the lid will fall off by people and cause injuries and accidents.Aging may cause odors to overflow and become smelly.We recommend replacing your grillwrap lid with a new lid as soon as it is punctured, grabbing or rusting.
Material: Banded steel plate (iron)
Handling plate thickness: 0.13 inch (3.2 mm) / 0.18 inch (4.5 mm)
Size of Handling: 11.8 x 15.7 x 19.7 inches (300 x 400 x 500 / 400 x 700 / 400 x 850 / 500 x 850 / 600 x 850 cm)
Handle: Positionable to specify mounting position (please purchase from other product round hole, long hole, and sliding type).
Reinforcement: No
Corner R: Customizable
Processing accuracy: ± 0.08 in (2.0 mm)
Country of Manufacture: Japan
Paint: Untreated. Corrosion resistance is improved by applying commercially available paint.
Quantity: 1PC
Banded steel plate (Shimako-han) is a board with continuous non-slip nibs on the surface, also known as a checkered plate or simply a stripe.The striping is aesthetically pleasing, and it is widely used as a steel sheet for floors, as well as a variety of veneers.It is also shaped to reduce weight and is very economical, with less wear on streaks.
When replacing the grid trap lid or groove lid, you need to check where to install.
We think that it has been installed in a frame like [1] - [3] if it is a big partner]
If you do not check the installation location, you may not be able to fit even if you place an order at a time may cause an accident.
You need to find the dimensions that match the shape of the frame so please check by type
If you want a gripping wrap, measuring where you place it on, then subtract the "allowance" from that dimension.
The allowance value is the gap between the lid and the frame of the grid wrap frame and the side groove.(Generally, about 0.08 - 0.11 inch (2 - 3 mm) per side).
Example 1. If the frame is 500 x 300, the lid size is about 496 x 296 - 494 x 294.
Please be careful as the frame may not be removed if there is a distortion due to aging etc.
[A] Type... If the frame shape is like [3] and this type is a relatively small lid.[B] Type: The frame shape matches the height of the floor with [1] so you can specify the height of the anti-slip/reinforcement material.[C] Type... When the frame shape is like [2] and [3], there is no need to match the height of the reinforcement material, and when you want to increase the load bearing strength in the center of the lid, it is the case that the lid size is relatively large.[D] Type... This is the type you choose when you have 2 gripper lids.The middle part (upper of the image) is designed to not ride on the border, so the strength is increased by attaching reinforcement material.[E] Type: T-type D type reinforcement is also effective when the lid has 2 lids.Reinforced interior with two vertical reinforcements for added strength.Recommended for large lids.
For A-type grid wrap lids, the following dimensions are required.
Product Length:
[L] Product Width:
[H] The position of the handle is attached (optional/extra charge)
Corner R: Corner processing
If you would like to install the handle, please purchase the "Grid Trap Lid Handle" together with this product and specify the dimensions of the Ha.
Please specify mm in [mm] when you input the dimensions.
For the handle, you can choose from 3 different types: round hole, long hole and slide type.
Please find the model number of the handle you need below and buy accordingly.
(You are sure to copy and paste the following model number)
Round hole cut (1 place) ... GT-OP_01-1
Round hole cut (2 places): GT-OP_01-2
Long hole cut (1 place) ... GT-OP_02-1
Long hole cut (2 places): GT-OP_02-2
Slide type (1 location): GT-OP_03-1
Slide type (2 places): GT-OP_03-2
You can round the corners (4 parts) of flat boards according to your preference. By specifying corner R, the corners are smooth and prevent injuries.Corner R size is available for your desired dimensions.
If you would like a corner R, please check the gift settings and fill in the gift message.
Examples of filling
If necessary: Corner R / Corner R wish etc.
If not needed: unwritten or no corner R etc.
Reference R Size:
R2-3: Round shape with a straw.Typical straws are approximately 0.2 - 0.2 inch (5 - 6 mm) in diameter (2.5 - 3.0 mm) in radius.
R5 - 7: About the size of AA batteries.AA batteries are approximately 0.5 inch (13 mm) in diameter (6.5 mm) in radius.