[Single Item]
This is an all-around model of INNO rod holder.
Uses a simple J-shaped hook that can be used for a wide range of applications, such as beaches, ships, throws, sweets, lure rods, parallel, shaking, 1 piece, gaff and fish patterns.
The grip diameter is compatible with up to 1.3 inches (32 mm), and the position of the holder can be moved forward, left and right.
Please check the Carmate compatibility chart before purchasing
This is an all-around model of INNO rod holder.
This simple J-shaped hook rod holder is compatible with a wide range of applications, such as beaches, ships, throws, sweets, lure rods, parallel, shaking, 1-piece, gaff and fish patterns.
Just hang it on the J-shaped hook and hold it with an elastic band, so you can operate it with one hand.
Supports grip diameters up to 1.3 inches (32 mm).
The newly designed J-hook can hold 1 piece thin tip.
If the diameter is less than 0.2 inch (5 mm) can be used with the included pad.
The grip side of the 2-piece rod can be secured with a rod belt etc.
The front side of the 2-piece rod should be the thinner side inside.
Supports grip diameters up to 1.3 inches (32 mm).
Can hold thin tips
2-piece rod grip side
2-piece rod front side
|
|
|
---|---|---|
It will slip when you ride it.The "coil type" that hangs between the driver and the passenger seat may slip off while driving. It is especially important to be cautious when driving on bad roads or sudden curves. |
Place in the back seatThe "coil type" needs to place the rod in the back seat or knock down the seat. This will limit the number of people that can enter the car. |
INNO Rod Holder SeriesThe INNO rod holder series can be firmly fixed to front and back hooks, so you dont have to worry about the rod slipping while driving. It also allows you to load it in the dead space under the ceiling so you dont have to knock down the seat or put the rod in the seat. |
|
|
|
---|---|---|
Reels hit each otherPlease note that the "belt type" on the front and rear assist grips are not fixed if they can be stored under the ceiling. On bad roads, sudden brakes, or sudden curves, the reel will be hard to hit each other. |
Hanging by rod weightThe "belt type" may hang on multiple rods when loaded. In that case, the distance between the head and the rod will be closer and may hit your head. |
INNO Rod Holder SeriesThe INNO rod holder series uses an assist grip mounting hole and the frame is made of metal. Therefore, you dont have to worry about the rod swinging due to vibration while riding, and the holder will hang on multiple loads. |
Short Frame Set | J-Hook Holder 7 | Optional holder 3 | Optional holder (silver) | Optional Holder (Black) | Grip Adapter | |
---|---|---|---|---|---|---|
Item No. | IF60 | IF65 | IF54 | IF50 | IF50BK | IF62 |
Specifications | Set of 2 frames that are 15.7 inches (40 cm) shorter than the standard IF14.Required for installation on hatchback vehicles with short straight roof. | Option to install between front and rear holder of IF14.It is required for a protruding rod, 2-piece rod, gaff or tamo handle and 1-piece rod. | Optional holder for additional applications.Can hold 2 rods with reels or only 3 additional rods | An option to turn your IF14 into a dual hold type. | An option to turn your IF14 into a dual hold type. | The option allows you to install the rod holder without removing the assist grip. |
This is an all-around model of INNO rod holder.
Uses a simple J-shaped hook that can be used for a wide range of applications, such as beaches, ships, throws, sweets, lure rods, parallel, shaking, 1 piece, gaff and fish patterns.
The grip diameter is compatible with up to 1.3 inches (32 mm), and the position of the holder can be moved forward, left and right.
Please check the Carmate compatibility chart before purchasing