[Attachment Color (Blue) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#39)]

[Attachment Color (Blue) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#36)]

[Attachment Color (Blue) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#35)]

[Attachment Color (Blue) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#32)]

[Attachment Color (Blue) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#31)]

[Attachment Color (Blue) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#34)]

[Attachment Color (Blue) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#33)]

[Attachment Color (Red) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#33)]

[Attachment Color (Red) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#32)]

[Attachment Color (Red) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#31)]

[Attachment Color (Red) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#36)]

[Attachment Color (Red) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#35)]

[Attachment Color (Red) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#34)]

[Attachment Color (Red) ｱﾀｯﾁﾒﾝﾄｻｲｽﾞ(#39)]

Product description

Brand new and unused

This is a collaboration set with OneS&Ms Breather System Kit and G-motos Silencer Stand.
The attachment is CNC machined from high quality aluminum duralumin and anodized aluminum for excellent strength and great for dress-up.
The Breather Silencer Stand is compatible with G-moto 42.7φ50.8φ Multi-silencer stand with two sizes of 42.7φ and 50.8φ in (42.7φ and 50.8φ) and has a hole to hang the spring on the top of the main unit and a hole for 4mm springs.


If you do not use the breather system, you can also use the oil filler cap with a special bolt!


Specifications: Total length of mesh hose: Approx. 31.5 inches (80 cm).
Mesh hose diameter: approx. 0.5 inches (12 mm)
Instructions for Breather Kit Included
Attachment screw size = Reference to the model column where it can be installed at the bottom.


Cap Color:
Breather Attachment Set: Available in 2 colors: Blue or Red


Set Contents:
1 x Breather Attachment
1 x Stainless Steel Breather Silencer Stand
Dedicated banjo bolt x 1
Dedicated banjo attachment x 1
2 x Copper Washers
Mesh hose 31.5 inches (80 cm) x 1
2 x hose bands


Breather Effect
By releasing blow by gases in the air, you can expect increased response (power) by reducing the amount of blow-by-gas fill in the engine.


Installation Notes:
Please refer to the included instruction manual (English language not guaranteed).
The silencer stand has two bolt holes of 0.4 inch (9 mm) (M9) and one 0.5 inch (12 mm) (M12 mm) bolt hole in between the stays, so please remove the bolt once and tighten it from the base of the rear step.
(CBR, remove the bolt on the left side of the rear tandem once to install).


Main Mountable Vehicle
★#35=M27×L10×P1.5
XJR400R(98-07)
V-MAX (90-07)
XJ400D
XJ400E
XJ550
XJ750
XJR400/R/R2 may vary in attachment sizes depending on the year.
93-96 (4HM only) P3.0
The 98-07 years (some 4HM and RH02J) are P1.5, so please check the pitch of the year and the pitch of the vehicle before purchasing.

ご注意（免責）＞必ずお読みください

≪注意事項≫
·ご覧になっている環境により色合いや明るさが異なる場合が御座います。
·ブリーザーKITはレース用部品となり、大気開放は保安基準を満たしませんので公道使用時や車検時はバンジョーアダブターを外し、オイルフィラーキャップの状態にして下さい。
·記載の車種であっても年式等でご使用出来ない場合がありますので、必ずオイルフィラーキャップのサイズをご確認の上、お買い求めください。
·商品自体の内部に小錆(サイスタのみ)、外部に保管傷·小傷等ありますので予めご了承下さい。
·取付けには加工が必要となる場合が御座いますので専門知識のあるショップ等で取付けを行って下さい。
·サイレンサースプリングは付属しておりませんので別途ご用意下さい。
·42.7φ及び50.8φのサイレンサーの場合であっても必ずお使いのサイレンサーの内径をご確認の上、お買い求め下さい。
·商品改良の為、予告なくデザインや仕様が変更となる場合が御座います。
·ワンズステッカーの色は赤もしくは青の1枚ランダムとなります。