Feature

●W 20cm x L 20cm (Set of 3) Black with Projection: 19g Virtually no elasticity. Heat iron on 15-20 seconds on a medium dry setting with press cloth. 0.95mm thick, so please adjust the adhesive level while checking the adhesive
●It can also be used to prevent slipping from crossing seams tape and jersey products such as chloroprene products, surf gloves, wader socks, etc
●Convex silicone rubber on the cross-section of the tape which weakens the adhesive strength, so it wont rub the skin directly on the base and will not peel off
●Please remember to peel off the backing of the seat before use
●If a hole is through, the sheet will not be able to be submerged in water. Please use a separate wetsuit bond before reinforcing with this product

Description

Non-slip seam sheet 7.9 x 7.9 inches (20 x 20 cm) / Black 3 piecesVirtually no elasticity.Reinforced seam tape intersection and holes in chloroprene jersey (through holes are reinforced after bonding use) for non-slip surf gloves and wader socks.

Can also be used with a fleece lining.If you press the iron on a large surface it will flatten the brush.Use iron iron tip or on small surface.

When used at intersection of seam tape where adhesion weakens, convex silicone rubber prevents skin from touching directly to the base fabric and is difficult to peel.

Contents not listed in the description are also included in the product page.Please refer to the product page.

Iron on medium heat setting and adjust between 15 and 20 seconds.It is thick, so you have to press the iron on it hardly, but if it is too strong it will break the convex rubber, so please look at and test it.

Iron on convex surface with press cloth.

If a hole is through, the sheet will not be able to be submerged in water.Please use a separate wetsuit bond before reinforcing with this product.

Iron Temperature

Synthetic fiber: Low temperature (approximate): 248°F (120°C); Cotton: Low temperature (approximate): 350°F (160°C).


Glue will protrude from the sheet when glued strongly	Use to prevent slipping, if you are not sure of the mold, please wet your hands and feet on the copy paper and mold it.Tape and trim the mold to the sheet. The non-slip sheet has almost no elasticity.Do not use on large surfaces.	Gloves and socks are difficult to stick.IntermediateUse ink pens or bath towels that wrap around your fingers and palms. Repeat work while making sure the seam sheet is firmly attached.

For palms and soles, please put towels in the towel and push the fabric out, so as to avoid denting surface.


1. Clean the treated area, salt or sand thoroughly with fresh water and dry thoroughly.	2. Spread the fabric over the ironing board and place the cut seam sheet on the part you want to repair.	3. Place a thin cloth such as a handkerchief over the seam sheet and press with an iron to make sure the sheet does not move. If you cut the corners of the sheet round, it will not peel off.


Convex silicone rubber total thickness 0.95mm Only the jersey side can be applied together.Rubber surface will melt	Please remember to remove the vinyl backing Note: This is a repair sheet for the jersey part.Avoid skins, pails, special fabrics, rubber surfaces or SCS.Heat may cause fabric to melt	Do not iron directly on the fabric or sheet to be treatedIt may burn the dough or melt the sheet. Place a thin cloth such as a handkerchief over the seam sheet and press with an iron to prevent the sheet from shifting.


	Includes 3 black jersey sheets.	Includes 2 Jersey Sheets Black and 2 Membrane Seat Black	Includes 3 non-slip seam sheets.	Old Package Includes 3 Wetsuit Repair Jersey Sheets
Features	Includes 3 jersey sheets to repair traditional elastic wetsuit holes.	Includes 2 jersey sheets to repair holes in the traditional elastic wetsuit and 2 thin membrane sheets with strong adhesion.	Includes 3 non-slip wetsuit repair sheets with convex silicone rubber.It does not touch the skin directly and does not peel off.	Repair jersey materials such as jersey material on the inner side of the wetsuit and other stocking-type waders and socks.

Non-slip seam sheet 7.9 x 7.9 inches (20 x 20 cm) / Black 3 piecesVirtually no elasticity.Reinforced seam tape intersection and holes in chloroprene jersey (through holes are reinforced after bonding use) for non-slip surf gloves and wader socks.

Can also be used with a fleece lining.If you press the iron on a large surface it will flatten the brush.Use iron iron tip or on small surface.

Iron on medium heat setting and adjust between 15 and 20 seconds.It is thick, so you have to press the iron on it hardly, but if it is too strong it will break the convex rubber, so please look at and test it.

Iron on convex surface with press cloth.

Glue will protrude from the sheet when glued strongly

Use to prevent slipping, if you are not sure of the mold, please wet your hands and feet on the copy paper and mold it.Tape and trim the mold to the sheet.

Gloves and socks are difficult to stick.IntermediateUse ink pens or bath towels that wrap around your fingers and palms.

For palms and soles, please put towels in the towel and push the fabric out, so as to avoid denting surface.

Convex silicone rubber total thickness 0.95mm

Please remember to remove the vinyl backing

Do not iron directly on the fabric or sheet to be treatedIt may burn the dough or melt the sheet.