[Board Only without 6 circuits and remote controller]
[6 circuits Connector included]
[Board Only with 8 circuits and no remote control]
[8 circuits No connector]
[6 circuits No connector]
[8-circuit Connector included]
[8 circuits without remote controller Connector included]
[6 circuits without remote controller Connector included]
[Minimum board only]
All circuits can be turned on and flashing | Traditionally only 2 circuits can be flashing, but all circuits can be switched between steady and flashing lights.This greatly increases the range of illumination.Flashing cycle can be increased or decreased in 10 milliseconds. |
Turn on and off times can be changed. | Now you can set the flashing and the time when the light is turned off.For example, if you turn it on for 1 second or turn it off for 2 seconds, or just turn it off for a while, the application range will be greatly expanded.This adjustment can be set individually for all circuits (with flashing settings).Turn on and off times can be increased or reduced in 10 milliseconds. |
The brightness of the LED can be adjusted to about 100 levels. | The brightness of the LED can be adjusted to approximately 100 levels per circuit.Even if you use the LED display, it will not be too bright and lose the atmosphere.Brightness adjustment is possible with up to 6 circuits. |
It is fluffy and bright when flashing and can be dimed with light. | The LEDs will be bright in an instant and darken in a matter of seconds, but the old bulbs will gradually turn on and off as they turn on and off.For example, turn signals a little in front of a car, etc., just became a snap in a moment! Chikat! It will break the atmosphere, but this setting will allow you to blink fluffy.You can also adjust the time to make it bright and dark.Adjustable up to 6 circuits |
Can be controlled by their own TV remote. | Now you can control it with the included remote and TV remote.Traditionally it was only a control with the included remote, but it will work the same when multiple models are arranged.This allows you to control multiple models individually.You can also use a universal remote control that can be switched from commercial TV manufacturers to control multiple models by one remote.Used in: Sharp, Panasonic, Toshiba, Hitachi, Pioneer, Sanyo, DX Antenna/Funai, Orion, Epson, Bi-Design, Nanao, Asma, DYNEX, TMY, neXXion, Hisense |
You want to light up your car models headlights and turn signals.
But you cant use it for electronic projects or soldering.
In that situation, you can easily decorate your lights.
In addition, you can use the infrared remote control to turn on and flashing from a distance.
The LED is a very small 0.06 x 0.03 inch (1.6 x 0.8 mm), so it can be incorporated into very small spaces, of course, the wiring is already soldered, so it can be easily incorporated into the model.
There are 3 kinds of circuits including 4 circuit models, 6 circuit models, 8 circuit models, and 2 LEDs per circuit.For example, car models can light up headlights, low beam, high beam, left and right turn signals, tail lights, brake lights, etc.Each circuit can be set to steady on or flashing.
When flashing, the flashing speed can be changed, and the lighting time and off time can be adjusted individually (up to 6 circuits).
For example, it is shiny! It can also be used as an anti-collision light for airplanes, such as when the light turns off for a while.
In addition, 100 brightness levels can be adjusted to prevent the atmosphere from being too bright (up to 6 circuits).
The main unit size is extremely small, and the battery is CR2032, so it can be installed inside even in 1/32 scale car models.
The main body is 1.4 inches (36 mm) (8 circuits) x 0.5 inches (31 mm) (6 circuits) x 0.5 inches (13 mm), 1.0 inches (26 mm) (4 circuits) x 0.5 inches (1
It can also be built into 1/32 car models and 1/43 mini cars.
The narrow width allows it to be built in in elongated shapes like airplane models.
Note: The shape of each part is subject to change.
Picture shows the model with 8 circuit connectors.
The LED can be illuminated 2 per circuit.
The LED has connectors and models without connectors, and models with connectors that do not require any soldering to the board.
Models without connectors need to solder the connection between the board and the cable, but they are more affordable.
Note: The shape of each part is subject to change.
By illuminating the lights, you can create a more realistic effect.
All circuits can be switched between steady and flashing.
The LED is a very small 0.06 inch (1.6 mm) x 0.8 inch (0.8 mm), so it can be easily installed in tight spaces.
Of course, the wires are soldered, so you can use them as is.
Choose either white or light bulb color
Bulb Color Model | This product | No remote control / Dimmable | Monoeye that continues to move | I Vulcan Lighted | |
---|---|---|---|---|---|
Features | LED is the bulb color. | This is a product | There is no remote control, but the brightness of each LED can be adjusted. | Monoeye keeps moving. | Eyes and Vulcan LED Lighting |
System Contents
Controller body
Remote Control Receiver
Switch
Battery Holder
Button battery (main unit and remote control)
Remote Control
Pre-wired LED.8 pcs 4 circuit models, 12 pcs 6 circuit models, 16 pcs 8 circuit models